ULTIM8™ JIG CORE KIT
Best for most EufyMake E1 users

° XL MAT (1 pc)
° MINI MAT (1 pc)
° SPRING CLIPS (6 pcs)
° 5.0 FIXTURES (24 pcs)
° 2.4 FIXTURES (24 pcs)
° 5.0 CAM LOCKS (12 pcs)
° 2.4 CAM LOCKS (12 pcs)
° BACKING PLATES (8 pcs)
° NEODYMIUM MAGNETS (20 pcs)


ULTIM8™ JIG DOUBLE
Best for users with more than one EufyMake E1

° XL MAT (2 pcs)
° MINI MAT (2 pcs)
° SPRING CLIPS (12 pcs)
° 5.0 FIXTURES (48 pcs)
° 2.4 FIXTURES (48 pcs)
° 5.0 CAM LOCKS (24 pcs)
° 2.4 CAM LOCKS (24 pcs)
° BACKING PLATES (16 pcs)
° NEODYMIUM MAGNETS (40 pcs)

ULTIM8™ JIG DELUXE KIT
Best for production users filling the bed with fixtures and printing many objects at once

° XL MAT (1 pc)
° MINI MAT (1 pc)
° SPRING CLIPS (6 pcs)
° 5.0 FIXTURES (48 pcs)
° 2.4 FIXTURES (48 pcs)
° 5.0 CAM LOCKS (24 pcs)
° 2.4 CAM LOCKS (12 pcs)
° BACKING PLATES (8 pcs)
° NEODYMIUM MAGNETS (20 pcs)
° XL CALIBRATION SHEETS (10 pcs)
° MINI CALIBRATION SHEETS (10 pcs)

_____________________________

EXTRAS


SET OF FIXTURES AND CAM LOCKS
For users planning on filling the bed with fixtures and printing many objects at once

° 5.0 FIXTURES (48 pcs)
° 2.4 FIXTURES (48 pcs)
° 5.0 CAM LOCKS (24 pcs)
° 2.4 CAM LOCKS (12 pcs)


SET OF BACKING PLATES AND MAGNETS
For users planning on printing on many flat thin materials

° BACKING PLATES (8 pcs)
° NEODYMIUM MAGNETS (20 pcs)


SET OF CALIBRATION SHEETS
For users who don't want to keep buying Eufy Mat replacements and need to calibrate machine

° XL CALIBRATION SHEETS (20 pcs)
° MINI CALIBRATION SHEETS (20 pcs)

_____________________________

REPLACEMENT PARTS


XL MAT
Replacement XL sized silicone JIG MAT

° XL MAT (1 pc)

MINI MAT
Replacement MINI sized silicone JIG MAT

° MINI MAT (1 pc)

SET OF SPRING CLIPS
Replacement set of spring clips

° SPRING CLIPS (6 pcs)

SETUP AND INSTALL INSTRUCTIONS

• Setup is simple: remove your bed, leave or remove the original sticky mat, place the ULTIM8™ JIG MAT on top, align it, and swing the SPRING CLIPS into place. (SPRING CLIP Installation Guide link below)
  
• Arrange FIXTURES as needed to position your parts. 
  
• Use FIXTURES alone or in combination with CAM LOCKS.
  

Make sure your parts are no more than 2mm below highest point of any fixture

• Parts ≥ 1.5 mm: use 2.4 FIXTURES  

• Parts > 4 mm: use 5.0 FIXTURES

• Use BACKING PLATES AND MAGNETS when ever you have parts less than 1.5mm.
  

Overspray peels off easily with a fingernail, by flexing the MAT, or even with heavy-duty packing tape.

• Spring Clip Installation Guide

•*Important to follow Spring Clip Installation guide or video.

* if you get a grinding sound during use with your JIG you need to check if Spring Clips are pushed in all the way and flush with sides of the Eufy Bed.

IMPORTANT: Center Magnet “Keep Out Zone” – EufyMake E1 Compatibility

The EufyMake E1 contains a large internal magnet located at the center of the build area. This magnetic field can interfere with:

• ULTIM8 JIG Magnets and Backing Plates
• Any ferrous (steel-based) objects

To ensure proper performance and avoid unintended movement or misalignment:

Keep-Out Requirement

Please maintain a 60mm (2.5 inch) wide “Keep Out Zone” centered on the build area.

If unsure, use the with of the E1 door handle as reference.

• Do not place magnets or backing plates within this zone
• Keep all ferrous materials outside this central strip
• Position your setup so all magnetic components remain beyond ± 30 mm from centerline

 Why This Matters

Placing magnets inside this zone may result in:

Loss of positioning accuracy

Unexpected attraction or shifting

Reduced effectiveness of the JIG system

Here is the PDF.

Machine Calibration

No need to calibrate your machine for use with our ULTIM8™ JIG, unless you care too.

Simply calibrate the bed without the MAT as usual.

If you would also like to run a print calibration on top of the mat, just lay one of our CALIBRATION SHEETS over the MAT and run the print calibration routine.

For Zero Point Calibration please download the pdf and the png image below.

• Zero Point Calibration Guide - PDF

________________________________________________________________________________________________________________________________

Using Calibration Sheets with Magnets & Backing Plates

When using Calibration Sheets together with our Magnets & Backing Plates, place magnets carefully to avoid interference with your print area, registration marks, and machine-specific magnetic keep-out zones.

For best results, position magnets around the outer edges of the Calibration Sheet where they provide secure hold-down without obstructing calibration targets or printing operations.Please refer to our placement diagram for ideal magnet locations, print-safe areas, and magnet keep-out zones.

Download Placement Diagram here.

• Fixture Caddy 3D printable caddy for organizing your FIXTURES, CAM LOCKS, accessories.

• Fixture Design Guides Guides & downloadables for designing your own fixtures.

• Pen Jig 3D printable individual pen holder that fits into our MATS.

• Printable Lower Mini Bed Model of EufyMake standard bed with reduced height .

• Golf Ball Jig 3D printable individual golf ball holder that fits into our MATS.

• Bottle Opener Jig 3D printable individual bottle opener holder that fits into our MATS.

• Shot Glass 3D printable individual shot glass holder that fits into our MATS.

Need Printed Parts?
Don't have a 3D printer? We can help with that! You can also purchase print outs from Jeff T.’s shop if you don't have a 3D printer. https://www.etsy.com/shop/psycho3dshop/?etsrc=sdt§ion_id=57341085